Deeper brick color with joints that stay packed
Brick Paver Sealing in Ponte Vedra Beach, FL
Ask for a free brick paver sealing price in Ponte Vedra Beach at (904) 694-6107.
- Brings out deeper paver color
- Fresh joint sand helps lock pavers in place
- Gives weeds less room to grow
- Makes the surface easier to keep clean
- Free estimate, no obligation
Request a Free Estimate
Free, no obligation.
Who seals brick pavers in Ponte Vedra Beach, and how soon will they call?
Yes, a local contractor handles brick paver sealing across Ponte Vedra Beach, FL, and a reply should land inside 1 business day, usually much sooner. Free estimates, no strings. The visit looks at the bricks, the joints and any shade or drainage trouble, so the quote fits the real job. To begin, call (904) 694-6107.
Brick drinks in water and stains faster than most people expect, so a courtyard or walkway can look tired after a few humid seasons. Brick paver sealing deepens the red and tan tones, helps lock the joints and makes spills easier to treat. Share how old the bricks are and whether they were ever sealed when you request a quote.
Why does brick soak up more than other pavers?
Brick is more absorbent than concrete, so it needs a product chosen for that. Unilock says brick pavers are more absorbent than concrete and suggests a matte or low gloss sealer, with slower drying in shade. To talk about what that means for your bricks, call (904) 694-6107.
A thirstier surface
Water and dirt move into brick faster, so the product should be chosen for brick, not borrowed from a driveway job.
Slower drying in shade
Unilock says drying runs slower in shade, so a shaded courtyard needs patience before the first coat.
Salt air
A Ponte Vedra Beach company says salt settles into the pores of unsealed pavers and, with ultraviolet light, leaves a chalky, washed-out look.
Humidity
That same company says humidity keeps surfaces from drying completely, which feeds algae and mildew on north sides.
Metal on the surface
Unilock says wire brushes can leave metal bits that rust and stain. Soft tools protect brick.
Aged color
Old brick often looks flat and dull. The right coat brings back depth without a plastic look.
How many coats does brick paver sealing take?
Two coats is the usual starting point, and brick that has never been sealed may take a third. A Ponte Vedra Beach company puts two coats as its standard and three on brick pavers that have never been sealed. A Florida concrete company describes a penetrating coat followed by a full coat. To ask what yours will need, call (904) 694-6107.
Never sealed
A Ponte Vedra Beach company uses three coats on brick like this, since the surface keeps soaking product in.
Sealed before
Two coats is common. A recoat on a surface in good shape may need only one, says a Florida concrete company.
Failed coating
Peeling or cloudy sealer may need stripping first, which a St. Augustine area company prices at $2.75 to $3.50 with restoration.
Sealer chemistry
A Ponte Vedra Beach company uses a two-part water-base urethane. Unilock recommends water-based sealers where possible for low odor.
Should brick pavers get a penetrating or a film sealer?
A penetrating sealer keeps the look natural, while a film coat adds sheen. A Jacksonville company gives 5 to 7 years for penetrating products and 3 to 5 years for wet look and semi-gloss. For a coastal courtyard, many owners start with matte. To see how each looks on your bricks, request a quote.
Penetrating matte
Soaks in without a surface film. The Jacksonville company says it lasts longer between coats.
Semi-gloss
A light sheen that deepens color. It wears faster than penetrating coats, according to the same company.
Wet look
Deepest color. The Jacksonville company says it turns cloudy white if applied to damp pavers or too thick.
How much does brick paver sealing cost in Ponte Vedra Beach?
Most brick jobs run from $150 for cleaning alone to $3,500 for stripping and restoring 1,000 square feet. Clean, sand and seal sits in the middle at $1.75 to $2.50 per square foot. For a price on your bricks, request a quote.
A third coat on never-sealed brick may add to the quote, and no page lists an exact figure for that. Ask for the coat count in writing. To go over your numbers, call (904) 694-6107.
| Brick service | Published rate per sq ft | 500 sq ft courtyard | 1,000 sq ft patio and walkways |
|---|---|---|---|
| Cleaning only | $0.30 to $0.50 | $150 to $250 | $300 to $500 |
| Clean and re-sand joints | $0.75 to $1.00 | $375 to $500 | $750 to $1,000 |
| Clean, sand and seal | $1.75 to $2.50 | $875 to $1,250 | $1,750 to $2,500 |
| Strip old sealer and restore | $2.75 to $3.50 | $1,375 to $1,750 | $2,750 to $3,500 |
Rates come from a St. Augustine area paver company that publishes each service by the square foot. No page gives a price for brick pavers alone, so the table multiplies those published pieces by the area. A Ponte Vedra Beach company uses three coats on brick that has never been sealed and says it quotes at a free estimate, so a third coat may add to the total. A Jacksonville company lists clean, sand and seal at $1.50 to $2.50 per square foot.
What is the brick paver sealing process?
The brick sealing process follows a fixed order, and dry time is the longest wait. Each step below is done before the next begins. To ask about timing, call (904) 694-6107.
1. Look for loose or sunken bricks
Lifted sections are reset first, since sealing locks in problems.
2. Protect plants and walls
Walls, planting and screens get covered before cleaners come out.
3. Wash at low pressure
A wide fan tip protects the joint sand, a point backed by Unilock's advice against narrow tips and wire brushes.
4. Treat algae and haze
North-side algae and white mineral haze get their own cleaners.
5. Dry and re-sand
A Ponte Vedra Beach company uses silica joint sand in tan, black, brown or grey. Joints go in before sealing.
6. Seal in coats
Two coats, or three on never-sealed brick, sprayed and back-rolled.
7. Cure and walk through
Unilock asks for up to 48 hours of dry weather to cure, with sprinklers off.
How soon can new brick pavers be sealed?
New brick needs a wait before its first coat. Unilock says 60 to 90 days, and the white haze can take up to a year to clear. A Jacksonville company gives a shorter window, 30 to 60 days. A Florida concrete company says a few months to about a year. Tell the contractor your install date when you request a quote.
Why wait
Sealer over haze traps minerals under the coat.
How to tell
A chalky white film on brick is usually efflorescence, which a contractor can confirm.
Meanwhile
A rinse is fine. Heavy products can wait.
How long does a brick sealer last in this climate?
Expect resealing every 2.5 to 3 years near the water, going by a Ponte Vedra Beach company, which also suggests one cleaning a year. Unilock gives 3 to 5 years as a general guide, and a Florida concrete company says about 3 years for most pavers. The wet season matters too: the Jacksonville area averages 28.81 inches of rain from June through September, over half the yearly total. To plan around that, call (904) 694-6107.
Near the beach
2.5 to 3 years, with the shorter end for full sun.
General guide
Unilock says reseal every 3 to 5 years, with heavy traffic shortening that.
Yearly rinse
Annual cleaning keeps algae from settling in.
Which brick areas around the house can be sealed?
Courtyards, walkways, steps and pool surrounds can all be sealed, and each wears differently. Shade, foot traffic and water all change the plan. To start with the area that bothers you most, request a quote.
Courtyards and entries
Shaded entries stay damp, and damp brick draws algae. Unilock says shade slows drying.
Front walks
Narrow paths sit beside beds and catch soil. A coat makes cleaning easier.
Garden steps
Steps need traction. Matte or low gloss finishes suit them, going by Unilock's advice on brick.
Pool surrounds
Brick near water needs a moisture check and a matte coat with grip.
What should I ask a contractor about my brick pavers?
Brick calls for a few questions that concrete jobs skip. Get the answers in writing so you can compare quotes. For help with the list, call (904) 694-6107.
Was this brick ever sealed?
A Ponte Vedra Beach company uses three coats on never-sealed brick and two as its standard.
Which sealer type is it?
That company uses a two-part water-base urethane. Unilock recommends water-based sealers where possible.
How will drying be checked?
A St. Johns County company says moisture should be evaluated before sealing.
What joint sand is going in?
A Ponte Vedra Beach company uses silica sand in tan, black, brown or grey.
Is a test patch possible?
A small patch shows how the color deepens before the whole courtyard is done.
Which Ponte Vedra Beach areas and nearby towns are covered for brick estimates?
Requests are welcome from across Ponte Vedra Beach and each community below. Each has its own page with local notes. If your street is close to a line, call (904) 694-6107.
What do sealed brick pavers look like in Ponte Vedra Beach?
Questions about brick paver sealing in Ponte Vedra Beach
How to seal your brick pavers?
The work follows a set order: inspect, wash, let the bricks dry, fill the joints with sand, then apply sealer in even coats. A Ponte Vedra Beach company puts three coats on brick pavers that have never been sealed, against two as its standard. A contractor handles the drying and product choice.
How long do paver sealers last on brick?
Expect about 2.5 to 3 years near the water, going by a Ponte Vedra Beach company, and Unilock gives 3 to 5 years as a general guide. A Jacksonville company says penetrating matte products can last 5 to 7 years. Full sun shortens all of these.
How much is sealant for pavers?
Product runs $80 to $150 a gallon, Unilock says, covering about 80 to 150 square feet depending on type. Brick soaks up more than concrete, so a never-sealed surface may take more product. Quotes usually come per square foot instead of per gallon.
Do I need to seal pavers in Florida?
Not strictly, but brick takes in moisture quickly. Unilock says brick is more absorbent than concrete. In a humid place with salt in the air, a sealer slows down stains and green growth, which is why many coastal homeowners choose it.
Why is paver sealing so expensive?
Cleaning, drying, new sand, taping and multiple coats make up most of the bill. A St. Augustine area company posts $1.75 to $2.50 per square foot for the full job, and $2.75 to $3.50 when old sealer is stripped and the surface restored.
How much does it cost to have brick pavers cleaned and sealed?
A 500 square foot courtyard runs about $875 to $1,250 at the St. Augustine area rate of $1.75 to $2.50. Cleaning alone is $0.30 to $0.50 per square foot. Never-sealed brick that needs a third coat may cost more, and no page publishes a brick rate.
Should brick pavers get a matte or a wet look sealer?
Unilock suggests a matte or low gloss product on brick and says drying runs slower in shade. A Jacksonville company says wet look can turn cloudy white if it goes on damp. Brick that holds moisture is a reason to pick matte.
Do brick pavers get white haze in Ponte Vedra Beach?
They can. White haze, called efflorescence, is a mineral film that usually clears in 2 to 3 months on new pavers and can take up to a year, according to Unilock. It has to be treated and rinsed before any coat goes on.
What joint sand works for brick pavers here?
A Ponte Vedra Beach company uses silica joint sand that sets as hard as polymeric sand or harder, in tan, black, brown or grey. A St. Augustine company uses kiln-dried ASTM C144 sand. Full joints also stop weeds and ants from moving in.
Need a price on your brick pavers?
Call or use the short form. A reply should arrive inside 1 business day, usually much sooner.
Free, no obligation